A Variety Of Trusted Experience
HWALU has a variety of professional, reliable and efficient crushing lines all around the world. So, customers have great confidence in us.
Menu
HWALU has a variety of professional, reliable and efficient crushing lines all around the world. So, customers have great confidence in us.
Stocking aluminum armor plate to the latest revisions of MIL-DTL-46027 and MIL-DTL-46063 in grades. 5083-H131 and 5059
1998-9-14 · ARMY MIL-DTL-46063 H-1998,This specification covers 7039 wrought aluminum alloy armor plate. The nominal thickness of armor plate covered by this specification is 1/2 inch to 4 inches, inclusive(see 3.7 and 6.2).
2000-6-12 · ARMOR PLATE, ALUMINUM ALLOY, 7039 ARMY MIL-DTL-46063 H (2)-2000 7039, ARMY MIL-DTL-46063 H .
Stocking aluminum armor plate to the latest revisions of MIL-DTL-46027 and MIL-DTL-46063 in grades. 5083-H131 and 5059
In this study, the special weld grooves was created on 7039 Al-Zn armor plate with different thickness of 12.7 and 38 mm and they were welded with MIG welding technique via multiple pass.
Stocking aluminum armor plate to the latest revisions of MIL-DTL-46027 and MIL-DTL-46063 in grades. 5083-H131 and 5059
2013-5-8 · Introduction. Aluminium / aluminum is one of the lightest available commercial metals with a density approximately one-third that of or . It can be easily fabricated into many forms such as foil, sheets, rod, , geometric shapes, and wire. Aluminium / aluminum 7039 alloy is a heat treatable wrought alloy.
2017-10-8 · Notes: Developed as armor plate for ballistic protection. Titanium (MIL-T-46077 and MIL-A-23556) Notes: 1970s alloy. Aluminum 2519-T87 (MIL-DTL-46192) Density: 2.823 g/cm3 Yield Strength: 400 MPa Ultimate Tensile Strength: 455 MPa. Composition (averages of allowable ranges) 92.77% Aluminum 5.85% 0.30% 0.30% Manganese 0.25% Silicon 0 ...
The plate specimens of Table 1 were rolled from of 7 to 8 tons which were cast vertically by the direct chill process. Both the casting and the rolling were performed in industrial plant equipment which makes commercial 5083 and 7039 aluminum armor plate.
1998-9-14 · ARMY MIL-DTL-46063 H-1998,This specification covers 7039 wrought aluminum alloy armor plate. The nominal thickness of armor plate covered by this specification is 1/2 inch to 4 inches, inclusive(see 3.7 and 6.2).
2021-5-11 · The most widely accepted aluminum alloys for armored plate applications are 5083, 6061 and 7039. 5083 meets the requirements of U.S. Military Specification MIL-A46027F while 7039 meets U.S. Military Specification MIL-A46063E. While 7039 is more effective in AP performance, 5083 fares better in FS applications.
Armor plate of alloy 7039 is considerably superior to armor plate of alloy 5083 for AP ballistic performance, but less so in FS ballistic performance. In fact, below 1.235 inch gauge, 7039 armor plate is rated below 5083 armor plate in FS ballistic performance according to the military specifications.
2001-5-1 · The damage in the aluminum foam backing plate is distributed over the whole span of the armor plate, which suggests that if foam is used behind the composite backing plate a good bonding between these layers is not important. In Design 3 (Fig. 17(d)), the composite inner layer served the purpose of distributing the load over the aluminum foam ...
2020-12-23 · MIL-DTL-46063 Armor Plate, Aluminum Alloy, 7039 This specification covers 7039 wrought aluminum alloy armor plate. The nominal thickness of armor plate covered by this specification is 1/2 inch to 4 inches, inclusive (see 3.7 and 6.2).
2016-5-18 · Aluminum alloys AA 2139, 2519, 5083, and 7039 are widely used in high-performance vehicular armor applications due to their high strength-to-weight ratio and ballistic performance [1–5].The unique attributes of these alloys allow for the vehicle to remain agile and fuel efficient while simultaneously maintaining a safe environment for its occupants.
7039 aluminum armor plate Alloy 7039 has superior protection against armor piercing and fragment threats, but it has substandard corrosion (especially stress corrosion) resistance. Alloy 7039 is more difficult to fusion weld and thus the only way to join individual components is .
high strength, high toughness aluminum alloys and armor alloys 5083-H131, 6061-T651, 7039-T64 and 2519-T87 are shown in Table II. ... 4 shows the rear surface of two inch plates of 7039, 5083 and ...
